User Guide & Instructions — Medical Ozone Care

1 Safety First

Never breathe ozone directly. Ozone is harmful to the lungs if inhaled. Always operate in a ventilated area and route unused ozone to the built-in destructor port.

Use medical-grade oxygen only. Do not use ambient air or industrial oxygen — ozone yield and purity depend on a clean O₂ feed.

Keep the unit dry, upright and on a stable surface during use.
Use only ozone-resistant tubing and accessories (supplied) — standard plastics degrade.
Do not block the destructor outlet or ventilation slots.
Ozone therapy must be administered by, or under the guidance of, a qualified practitioner.
Switch off and disconnect oxygen before connecting or removing accessories.

2 Setup & Connection

Choose your oxygen source. A medical oxygen cylinder (with the matching AOT regulator) or an oxygen concentrator with a correct flow meter.
Fit the regulator. Attach the AOT oxygen regulator that matches your cylinder valve (870 pin-index, 540 threaded, or BN bull-nose).
Connect oxygen to the generator. Run the silicone hose from the regulator outlet to the generator's O₂ inlet port.
Connect the output. Attach tubing to an O₃ outlet, then to your application accessory (stone diffuser for liquids, or male luer lock / 3-valve lock).
Connect the destructor. Route any unused-ozone line to the O₃ destructor port so excess ozone is neutralised.
Power up. Plug in the 100–240 V adaptor. The unit runs on 110–220 V AC at just 15 W.

3 Operation

Select the mode. Press the M1 / M2 switch. M1 covers levels L1–L4 (lower range); M2 covers L5–L6 (higher range).
Set the oxygen flow. Adjust the flow on your regulator (1/32 … 1 L/min). Lower flow = higher concentration.
Choose the level. Press an L1–L4 button (M1) or use the L5/L6 knobs (M2).
Wait for stable output. Allow about 30 seconds for the ozone concentration to stabilise.
Read the value. Cross-reference flow + level on the concentration chart below.

Example: For ~30 µg/ml, press M1, then L2, and set the regulator to 1/8 L/min (= 30.2 µg/ml).

4 After Use & Care

After therapy, run oxygen-only for a few seconds to flush residual ozone, then power off.
Disconnect the oxygen supply and depressurise the regulator.
Rinse and dry reusable accessories; replace stone diffusers and tubing periodically.
Wipe the housing with a dry or slightly damp cloth — never immerse the unit.
Store in a cool, dry place away from direct sunlight.

5 Warranty & Support

The medical ozone generators are covered by a 1-year warranty against manufacturing defects. Genuine spare accessories are available. For support call +91 99588 03980 or email medicalozonecare@gmail.com. There are no user-serviceable parts inside.

Concentration Chart (µg/ml)

Find your oxygen flow rate (left) and read across to your selected level. Modes: M1 = L1–L4, M2 = L5–L6.

O₂ Flow	Mode M1				Mode M2
O₂ Flow	L1	L2	L3	L4	L5	L6
1 L/min	4.4	5.3	6.1	6.9	12.6	15.8
3/4 L/min	5.7	6.7	7.8	8.7	15.9	21.6
1/2 L/min	8.9	10.4	11.9	13.2	22	37.3
1/4 L/min	16.5	19.2	21.8	24.1	39.7	51.5
1/8 L/min	26.2	30.2	33.9	37.2	62.8	72.8
1/16 L/min	38.4	43.9	48.5	52	82	89.9
1/32 L/min	—	—	—	—	86	92.5

All values in µg/ml (mg/L). "—" = not available at that flow.

Need help? Call +91 99588 03980 or WhatsApp us for first-time setup support.